I2C: ready DRAM: smem ram ptable found: ver: 1 len: 4 2 GiB NAND: ONFI device found ID = 1580a12c Vendor = 2c Device = a1 Board Type: 0x201 Start up the normal boot... resetting ... Welcome To HUAWEI Wlan World 611 (Jan 28 2019 - 21:44:52 +0800) I2C: ready DRAM: smem ram ptable found: ver: 1 len: 4 2 GiB NAND: ONFI device found ID = 1580a12c Vendor = 2c Device = a1 Board Type: 0x201 In: serial@78B3000 Out: serial@78B3000 Err: serial@78B3000 machid: 8010001 Net: Ethernet Mac: 88-86-03-2D-3B-A0 Build:5 Main:2 Branch:0, 2017.5.19 load firmware success EDMA ver 1 hw init Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7) RxDesc:1 (15-15) RxFill:1 (7-7) ipq807x_edma_alloc_rings: successfull ipq807x_edma_setup_ring_resources: successfull ipq807x_edma_configure_rings: successfull ipq807x_edma_hw_init: successfull eth0 Start Up time(s) : 1 Image: Current Bootup is B Image: Current Bootup is B POST test: Begin Testing PHY0 : Passed. Testing PHY1 : Passed. Testing DDR : Passed. Testing Nor Flash: Passed. Testing Nand Flash: Passed. Saving POST results: Done POST test: End Crashdump magic found, initializing dump activity.. Press f or F to stop Auto-Boot in 3 seconds: 2  1  0 No need to update from sys-boot! ## Loading kernel from FIT Image at 46000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage ## Loading fdt from FIT Image at 46000000 ... Using 'config@1' configuration Trying 'fdt@1' fdt subimage Booting using the fdt blob at 0x464ad134 Uncompressing Kernel Image ... OK Loading Device Tree to 4a3ea000, end 4a3ff891 ... OK Using machid 0x8010001 from environment Starting kernel ... Jumping to AARCH64 kernel via monitor FWD_MEM: aligned address ffffffc06b000000 FWD_MEM: 00000000ac000000 FWD_MEM: Allocating 256MB (65536 pages) of memory at addr ffffffc06b000000 **** Total Boot time: 3910 ms, uncompress initrd cost 0 ms **** Bad inittab entry at line 11 Bad inittab entry at line 12 starting pid 1446, tty '': '-/etc/init.d/rcS' hello mkdir: can't create directory '/opt/corefile/': Read-only file system read content=/modules/4.1.51/net/wifi_module.ko,len=35. qca ssdk ko insmod begin ...... done. read content=/root/cap32,len=12. done. read content=/modules/msu.ko,len=16. done. read content=/root/monitor,len=14. done. read content=/root/ble.bin,len=14. done. read content=/root/vos.o,len=12. done. read content=/root/cmdtree.bin,len=18. done. read content=/root/db.dat,len=13. done. read content=/root/infoeng.res,len=18. done. attach mtd2. pass attach mtd2. mount RWFS successfully Mount fsimage type: patch User fs folder : /opt Loop device : /dev/loop0 Mount folder : /mnt/patch 131072+0 records in 131072+0 records out 131072 bytes (128.0KB) copied, 9.042135 rproc_init_debugfs: can't create debugfs dir cnss: Unable to create IPC log context! ####### auto_start RESET_SUBSYS_COUPLED seconds, 14.2KB/s wifi start set ulMcThValue: 512 __mm_init_module btcoex_support 0 wlan_prio_gpio 0 wmi_handle:ffffffc07b45a000 :wifi1 ACS not enabled wmi_handle:ffffffc05b885000 :wifi0 ACS not enabled @@@@@ __ol_ath_attach(in): soc= ffffffc05e600880 ###############Load radio 1 ###############Radio[1] enter cs thread ###############Load radio 0 ###############Radio[0] enter cs thread wifi start end ----- Monitor begin ----- delete the digicert cer file copy the digicert cer file to usnetif_napi_add() called with weight 100 on device eth1 er dir delete the local cer filer copy the local cer file to user dir cap32 start, build time 22:39:44 Module MEM Init ...... OK! Module DIAG Init ...... OK! Module PBUF Init ...... OK! Module IM Init ...... OK! Module IIC Init ...... OK! Module HAL Init ...... OK! Module Timer Init ...... OK! Module TIME Init ...... OK! MSS_Global_Init success! MSC Process run on core [0], PID = [1714] MSC_TCTL_Init SucMSS_PUB_Init Succ, ret = 0 AP_Board_Cfg Succ, ret = 0 Module MEM Init ...... OK! Module DIAG Init ...... OK! Module PBUF Init ...... OK! Module IM Init ...... OK! Module IIC Init ...... OK! Module HAL Init ...... OK! Module Timer Init ...... OK! Module TIME Init ...... OK! MSS_Global_Init Succ, ret = 0 MSU Init OK MSU_Init Succ, ret = 0 MSS_IM_InstGlobalInit Succ, ret = 0 MSS_Local_Init Succ, ret = 0 c! u32Ret = 0 MSC goto scheduler! VOS_Start ...... PPI_DEV_SysInit begin. CDEV_InitProduct Success ! DEV_EVT_InitEvtData Success ! PPI_DEV_SysInit End. Task GRSA Init......Ok......OK VRP_SockTm_Init create............OK [DEBUG]Drv_Init begin ............ [DEBUG]Drv_Init PortNum is 5 System recover configuration .....OK! Press any key to get started