=================================================================== MT7621 stage1 code Dec 16 2019 17:45:55 (ASIC) CPU=500000000 HZ BUS=166666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11000000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL2 FB_DL: 0x12, 1/0 = 537/487 49000000 PLL4 FB_DL: 0x13, 1/0 = 556/468 4D000000 PLL3 FB_DL: 0x16, 1/0 = 639/385 59000000 DDR patch working do DDR setting..[01F40000] Apply DDR3 Setting...(use default AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 000E:| 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 000F:| 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0010:| 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0011:| 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DRAMC_DQSCTL1[0e0]=13000000 DRAMC_DQSGCTL[124]=80000033 rank 0 coarse = 15 rank 0 fine = 56 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_DDR2CTL[07c]=C287221D DRAMC_PADCTL4[0e4]=000022B3 DRAMC_DQIDLY1[210]=02020003 DRAMC_DQIDLY2[214]=01020202 DRAMC_DQIDLY3[218]=02030002 DRAMC_DQIDLY4[21c]=03010201 DRAMC_R0DELDLY[018]=00001B1A ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 0 0 0 0 0 0 0 0 0 0 10 | 0 0 0 0 0 0 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =26 DQS1 = 27 ================================================================== bit DQS0 bit DQS1 0 (0~47)23 8 (0~51)25 1 (0~52)26 9 (0~54)27 2 (0~48)24 10 (0~49)24 3 (0~48)24 11 (0~51)25 4 (0~48)24 12 (0~52)26 5 (0~48)24 13 (0~50)25 6 (0~48)24 14 (0~52)26 7 (0~50)25 15 (0~48)24 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 3 0 2 2 2 2 2 1 2 0 10 | 3 2 1 2 1 3 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) DRAMC_DQODLY1[200]=88888888 DRAMC_DQODLY2[204]=88888888 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=500000000 HZ BUS=166666666 HZ =================================================================== U-Boot SPL 2018.09 (Feb 20 2021 - 09:43:17 +0800) Trying to boot from NOR U-Boot 2018.09 (Feb 20 2021 - 09:43:17 +0800) CPU: MediaTek MT7621AT ver 1, eco 3 Clocks: CPU: 880MHz, DDR: 1200MHz, Bus: 220MHz, XTAL: 40MHz Model: MediaTek MT7621 reference board DRAM: 128 MiB Loading Environment from SPI Flash... SF: Detected xm25qh128a with page size 256 Bytes, erase size 64 KiB, total 16 MiB *** Warning - bad CRC, using default environment In: uartlite0@1e000c00 Out: uartlite0@1e000c00 Err: uartlite0@1e000c00 Net: Warning: eth@1e100000 (eth0) using random MAC address - ba:6e:8b:bd:30:cf eth0: eth@1e100000 reset button is not pressed for 10s. turn on led Hit any key to stop autoboot: 0 [?25l *** U-Boot Boot Menu *** Press UP/DOWN to move, ENTER to select 1. Startup system (Default) 2. Upgrade firmware 3. Upgrade bootloader 4. Upgrade bootloader (advanced mode) 5. Load image 0. U-Boot console Hit any key to stop autoboot: 3  2  1  0 [?25hincorrect device type in firmware ## Loading kernel from FIT Image at bfca0000 ... Using 'config-1' configuration Trying 'kernel-1' kernel subimage Description: MIPS OpenWrt Linux-5.10.83 Type: Kernel Image Compression: lzma compressed Data Start: 0xbfca00e4 Data Size: 2610583 Bytes = 2.5 MiB Architecture: MIPS OS: Linux Load Address: 0x80001000 Entry Point: 0x80001000 Hash algo: crc32 Hash value: 10fa971b Hash algo: sha1 Hash value: 4cfd797d8c395b8e833521db688723ab11e85eff Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at bfca0000 ... Using 'config-1' configuration Trying 'fdt-1' fdt subimage Description: MIPS OpenWrt tplink_eap615-wall-v1 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0xbff1d7c0 Data Size: 11042 Bytes = 10.8 KiB Architecture: MIPS Hash algo: crc32 Hash value: 00a14628 Hash algo: sha1 Hash value: d70e7925341da668ffde400f90b667d0f27a7cd0 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0xbff1d7c0 Uncompressing Kernel Image ... OK Loading Device Tree to 87e67000, end 87e6cb21 ... OK [ 0.000000] Linux version 5.10.83 (stijn@taz) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r17684+1-b4a3c20aa4) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Dec 13 15:41:58 2021 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is TP-Link EAP615-Wall v1 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s29776 r8192 d23472 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Writing ErrCtl register=000319b1 [ 0.000000] Readback ErrCtl register=000319b1 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 119856K/131072K available (6364K kernel code, 590K rwdata, 1312K rodata, 1256K init, 228K bss, 11216K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x3d4/0x5c4 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000014] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.007942] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.016917] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.083085] pid_max: default: 32768 minimum: 301 [ 0.087823] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.095026] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.104825] rcu: Hierarchical SRCU implementation. [ 0.109781] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.117703] smp: Bringing up secondary CPUs ... [ 0.122759] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.122770] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.122781] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.122857] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.177652] Synchronize counters for CPU 1: done. [ 0.209664] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.209673] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.209680] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.209726] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.268721] Synchronize counters for CPU 2: done. [ 0.299097] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.299105] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.299112] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.299159] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.353900] Synchronize counters for CPU 3: done. [ 0.383759] smp: Brought up 1 node, 4 CPUs [ 0.391278] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.401089] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.408037] pinctrl core: initialized pinctrl subsystem [ 0.414905] NET: Registered protocol family 16 [ 0.420621] thermal_sys: Registered thermal governor 'step_wise' [ 0.421424] cpuidle: using governor teo [ 0.452962] random: fast init done [ 0.472665] clocksource: Switched to clocksource GIC [ 0.479545] NET: Registered protocol family 2 [ 0.484112] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.491871] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.500207] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.507788] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.514784] TCP: Hash tables configured (established 1024 bind 1024) [ 0.521205] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.527689] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.534827] NET: Registered protocol family 1 [ 0.539115] PCI: CLS 0 bytes, default 32 [ 0.545321] workingset: timestamp_bits=30 max_order=15 bucket_order=0 [ 0.555290] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.561034] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.572985] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.578783] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.584629] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.591035] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.598903] printk: console [ttyS0] disabled [ 0.603239] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.612221] printk: console [ttyS0] enabled [ 0.612221] printk: console [ttyS0] enabled [ 0.620482] printk: bootconsole [early0] disabled [ 0.620482] printk: bootconsole [early0] disabled [ 0.632517] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 0.639482] spi-nor spi0.0: XM25QH128A (16384 Kbytes) [ 0.644682] 9 fixed-partitions partitions found on MTD device spi0.0 [ 0.651006] Creating 9 MTD partitions on "spi0.0": [ 0.655798] 0x000000000000-0x000000080000 : "u-boot" [ 0.661779] 0x000000080000-0x000000090000 : "partition-table" [ 0.668492] 0x000000090000-0x0000000a0000 : "product-info" [ 0.674860] 0x0000000a0000-0x000000d90000 : "firmware" [ 0.681030] 2 fit-fw partitions found on MTD device firmware [ 0.686754] Creating 2 MTD partitions on "firmware": [ 0.691711] 0x000000000000-0x000000290000 : "kernel" [ 0.697461] 0x000000290000-0x000000cf0000 : "rootfs" [ 0.703190] mtd: device 5 (rootfs) set to be root filesystem [ 0.708975] 1 squashfs-split partitions found on MTD device rootfs [ 0.715177] 0x0000009e0000-0x000000cf0000 : "rootfs_data" [ 0.721281] 0x000000d90000-0x000000df0000 : "user-config" [ 0.727510] 0x000000f30000-0x000000fb0000 : "mutil-log" [ 0.733600] 0x000000fb0000-0x000000ff0000 : "oops" [ 0.739207] 0x000000ff0000-0x000001000000 : "radio" [ 0.744984] 0x000000000000-0x000001000000 : "full" [ 0.759368] libphy: Fixed MDIO Bus: probed [ 0.802741] pm: rgmii [ 0.802841] pm: rgmii [ 0.806290] libphy: mdio: probed [ 0.812486] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.818746] mt7530 mdio-bus:1f: supply core not found, using dummy regulator [ 0.826068] mt7530 mdio-bus:1f: supply io not found, using dummy regulator [ 0.836758] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 21 [ 0.845357] mtk_soc_eth 1e100000.ethernet: generated random MAC address 92:6b:9c:43:23:52 [ 0.854300] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 21 [ 0.865652] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 0.872383] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 0.880563] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 0.888815] mt7621-pci 1e140000.pcie: Parsing DT failed [ 0.896226] NET: Registered protocol family 10 [ 0.902054] Segment Routing with IPv6 [ 0.905856] NET: Registered protocol family 17 [ 0.910645] 8021q: 802.1Q VLAN Support v1.8 [ 0.918172] gpio-export gpio-export: 1 gpio(s) exported [ 0.923623] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 0.929844] mt7530 mdio-bus:1f: supply core not found, using dummy regulator [ 0.937157] mt7530 mdio-bus:1f: supply io not found, using dummy regulator [ 0.958066] pm: rgmii [ 0.961945] libphy: dsa slave smi: probed [ 0.968634] mt7530 mdio-bus:1f lan0 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) [ 0.979442] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) [ 0.990221] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) [ 1.001034] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) [ 1.012109] pm: rgmii [ 1.012334] mt7530 mdio-bus:1f (unnamed net_device) (uninitialized): validation of rgmii with support 0000000,00000000,00006280 and advertisement 0000000,00000000,00006280 failed: -22 [ 1.031055] mt7530 mdio-bus:1f (unnamed net_device) (uninitialized): failed to connect to PHY: -EINVAL [ 1.040366] mt7530 mdio-bus:1f (unnamed net_device) (uninitialized): error -22 setting up PHY for tree 0, switch 0, port 5 [ 1.051713] pm: rgmii [ 1.052291] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 1.065173] DSA: tree 0 setup [ 1.068444] rt2880-pinmux pinctrl: pcie is already enabled [ 1.074015] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 1.080727] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 1.088906] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 1.097171] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 1.104918] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 1.212749] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 1.218326] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 1.324025] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.330962] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.335836] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.340697] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.350133] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.356498] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 1.363365] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.370212] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.375692] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 1.385888] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.391885] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.398153] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid [ 1.405187] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000] [ 1.410978] pci 0000:00:00.0: supports D1 [ 1.414985] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.421321] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.427364] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.433625] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid [ 1.440642] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000] [ 1.446442] pci 0000:00:01.0: supports D1 [ 1.450434] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.457681] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.465694] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.473923] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280 [ 1.479948] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 1.486995] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit pref] [ 1.493701] pci 0000:01:00.0: reg 0x18: initial BAR value 0x00000000 invalid [ 1.500718] pci 0000:01:00.0: reg 0x18: [mem size 0x00004000 64bit pref] [ 1.507417] pci 0000:01:00.0: reg 0x20: initial BAR value 0x00000000 invalid [ 1.514461] pci 0000:01:00.0: reg 0x20: [mem size 0x00001000 64bit pref] [ 1.521254] pci 0000:01:00.0: supports D1 D2 [ 1.525521] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.532149] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.548490] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.553739] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.559808] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.566583] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref] [ 1.573804] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.580628] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280 [ 1.586675] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 1.593715] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000 64bit pref] [ 1.600400] pci 0000:02:00.0: reg 0x18: initial BAR value 0x00000000 invalid [ 1.607431] pci 0000:02:00.0: reg 0x18: [mem size 0x00004000 64bit pref] [ 1.614135] pci 0000:02:00.0: reg 0x20: initial BAR value 0x00000000 invalid [ 1.621151] pci 0000:02:00.0: reg 0x20: [mem size 0x00001000 64bit pref] [ 1.627960] pci 0000:02:00.0: supports D1 D2 [ 1.632213] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.638864] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.655222] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.660445] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.666542] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff] [ 1.673320] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref] [ 1.680517] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.687169] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.693778] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.700713] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 1.707313] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.714265] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.721025] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 1.728235] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff] [ 1.735015] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref] [ 1.742207] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff] [ 1.748989] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff] [ 1.755778] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 1.762539] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 1.769325] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 1.777068] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 1.784813] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 1.792534] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.797493] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 1.804271] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.811030] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref] [ 1.818250] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref] [ 1.825992] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref] [ 1.833735] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref] [ 1.841454] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.846414] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 1.853191] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff] [ 1.859950] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref] [ 1.877328] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.888524] Freeing unused kernel memory: 1256K [ 1.893087] This architecture does not have kernel memory protection. [ 1.899516] Run /sbin/init as init process [ 1.904065] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 2.615646] init: Console is alive [ 2.619440] init: - watchdog - [ 3.355817] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.446472] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.463068] init: - preinit - [ 4.485486] random: jshn: uninitialized urandom read (4 bytes read) [ 4.567085] random: jshn: uninitialized urandom read (4 bytes read) [ 4.601495] random: jshn: uninitialized urandom read (4 bytes read) [ 5.331267] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 5.340024] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 5.342859] mt7530 mdio-bus:1f lan0: configuring for phy/gmii link mode [ 5.355401] 8021q: adding VLAN 0 to HW filter on device lan0 [ 5.363692] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.464356] random: crng init done [ 9.467782] random: 6 urandom warning(s) missed due to ratelimiting [ 9.493678] mt7530 mdio-bus:1f lan0: Link is Up - 1Gbps/Full - flow control off [ 9.501014] IPv6: ADDRCONF(NETDEV_CHANGE): lan0: link becomes ready [ 9.744098] jffs2: notice: (537) jffs2_build_xattr_subsystem: complete building xattr subsystem, 15 of xdatum (11 unchecked, 1 orphan) and 20 of xref (1 dead, 0 orphan) found. [ 9.762067] mount_root: switching to jffs2 overlay [ 9.784916] overlayfs: upper fs does not support tmpfile. [ 9.803768] urandom-seed: Seeding with /etc/urandom.seed [ 10.030055] mt7530 mdio-bus:1f lan0: Link is Down [ 10.044768] procd: - early - [ 10.047876] procd: - watchdog - [ 10.712840] procd: - watchdog - [ 10.717448] procd: - ubus - [ 10.804231] procd: - init - Please press Enter to activate this console. [ 11.543725] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.815659] urngd: v1.0.2 started. [ 11.845504] GACT probability on [ 11.850000] Mirror/redirect action on [ 11.864085] u32 classifier [ 11.866808] input device check on [ 11.870447] Actions configured [ 11.885384] Loading modules backported from Linux version v5.15-rc6-0-g519d81956ee2 [ 11.893055] Backport generated by backports.git v5.15-rc6-1-0-gd44432d6 [ 12.175039] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=22 [ 12.180466] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 12.186143] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002) [ 12.192988] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=23 [ 12.198437] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 12.204119] mt7915e 0000:02:00.0: enabling device (0000 -> 0002) [ 12.235268] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a [ 12.235268] [ 12.620253] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304 [ 12.661503] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323 [ 12.789673] kmodloader: done loading kernel modules from /etc/modules.d/* [ 20.339047] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 20.352588] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 20.360854] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 20.365396] mt7530 mdio-bus:1f lan0: configuring for phy/gmii link mode [ 20.376581] 8021q: adding VLAN 0 to HW filter on device lan0 [ 20.386103] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 20.393937] switch: port 1(lan0) entered blocking state [ 20.399172] switch: port 1(lan0) entered disabled state [ 20.405593] device lan0 entered promiscuous mode [ 20.410253] device eth0 entered promiscuous mode [ 20.477601] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 20.484939] 8021q: adding VLAN 0 to HW filter on device lan1 [ 20.494225] switch: port 2(lan1) entered blocking state [ 20.499515] switch: port 2(lan1) entered disabled state [ 20.506239] device lan1 entered promiscuous mode [ 20.524939] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 20.532148] 8021q: adding VLAN 0 to HW filter on device lan2 [ 20.541369] switch: port 3(lan2) entered blocking state [ 20.546741] switch: port 3(lan2) entered disabled state [ 20.553229] device lan2 entered promiscuous mode [ 20.577199] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 20.584390] 8021q: adding VLAN 0 to HW filter on device lan3 [ 20.593834] switch: port 4(lan3) entered blocking state [ 20.599084] switch: port 4(lan3) entered disabled state [ 20.605898] device lan3 entered promiscuous mode [ 23.425778] switch: port 5(wl5-lan) entered blocking state [ 23.431319] switch: port 5(wl5-lan) entered disabled state [ 23.437601] device wl5-lan entered promiscuous mode [ 23.495085] mt7530 mdio-bus:1f lan0: Link is Up - 1Gbps/Full - flow control off [ 23.502544] switch: port 1(lan0) entered blocking state [ 23.508145] switch: port 1(lan0) entered forwarding state [ 23.514959] IPv6: ADDRCONF(NETDEV_CHANGE): switch: link becomes ready [ 23.522343] IPv6: ADDRCONF(NETDEV_CHANGE): switch.20: link becomes ready [ 23.530046] IPv6: ADDRCONF(NETDEV_CHANGE): switch.30: link becomes ready [ 23.537442] IPv6: ADDRCONF(NETDEV_CHANGE): switch.54: link becomes ready [ 23.544862] IPv6: ADDRCONF(NETDEV_CHANGE): switch.99: link becomes ready [ 24.231540] IPv6: ADDRCONF(NETDEV_CHANGE): wl5-lan: link becomes ready [ 24.238599] switch: port 5(wl5-lan) entered blocking state [ 24.244432] switch: port 5(wl5-lan) entered forwarding state [ 24.582341] switch: port 6(wl5-guest) entered blocking state [ 24.588350] switch: port 6(wl5-guest) entered disabled state [ 24.594830] device wl5-guest entered promiscuous mode [ 24.623344] switch: port 6(wl5-guest) entered blocking state [ 24.629050] switch: port 6(wl5-guest) entered forwarding state [ 24.713300] switch: port 6(wl5-guest) entered disabled state [ 25.129436] IPv6: ADDRCONF(NETDEV_CHANGE): wl5-guest: link becomes ready [ 25.136558] switch: port 6(wl5-guest) entered blocking state [ 25.142259] switch: port 6(wl5-guest) entered forwarding state [ 25.521295] switch: port 7(wl24-lan) entered blocking state [ 25.527027] switch: port 7(wl24-lan) entered disabled state [ 25.533640] device wl24-lan entered promiscuous mode [ 25.539030] switch: port 7(wl24-lan) entered blocking state [ 25.544780] switch: port 7(wl24-lan) entered forwarding state [ 25.643030] switch: port 7(wl24-lan) entered disabled state [ 25.959192] uledd: v1.0.1 started. [ 34.106399] IPv6: ADDRCONF(NETDEV_CHANGE): wl24-lan: link becomes ready [ 34.113350] switch: port 7(wl24-lan) entered blocking state [ 34.118909] switch: port 7(wl24-lan) entered forwarding state [ 34.248947] switch: port 8(wl24-guest) entered blocking state [ 34.254808] switch: port 8(wl24-guest) entered disabled state [ 34.261105] device wl24-guest entered promiscuous mode [ 34.268912] switch: port 8(wl24-guest) entered blocking state [ 34.275018] switch: port 8(wl24-guest) entered forwarding state [ 34.466851] IPv6: ADDRCONF(NETDEV_CHANGE): wl24-guest: link becomes ready [ 34.585377] switch: port 9(wl24-iot) entered blocking state [ 34.591015] switch: port 9(wl24-iot) entered disabled state [ 34.597705] device wl24-iot entered promiscuous mode [ 34.609534] switch: port 9(wl24-iot) entered blocking state [ 34.615178] switch: port 9(wl24-iot) entered forwarding state [ 34.847592] IPv6: ADDRCONF(NETDEV_CHANGE): wl24-iot: link becomes ready